Guide

How Far Apart Are Wall Studs? 16 vs 24 Inch Spacing

In most houses, wall studs are 16 inches apart, measured from the center of one stud to the center of the next. Newer homes and some exterior walls use 24 inches, and older homes can be anywhere from 12 to 24. This guide explains which spacing to use, what the building code allows, how many studs each spacing needs and how to find the studs in a finished wall.

Quick answer

Standard wall studs are 16 inches on center: the centers of neighbouring studs are 16 in apart, leaving about 14½ in of open space between them. 24 in on center is allowed for many single-story and non-bearing walls and needs about a third fewer studs.

Bar chart: studs on layout for a 20 foot wall — 21 studs at 12 inches on center, 16 at 16 inches, 11 at 24 inches
Studs on layout for one 20 ft wall, before corners, openings and waste.
Calculators for this guide

Standard stud spacing

Stud spacing is measured on center (o.c.): from the middle of one stud to the middle of the next. A 2×4 is 1½ in thick, so at 16 in on center the open space between studs is about 14½ in, and at 24 in it is about 22½ in.

SpacingWhere it's usedGap between studs
16 in o.c.The default for most interior and exterior walls, and for any 2×4 wall carrying a floor above14½ in
24 in o.c.Non-bearing interior walls, single-story or top-floor walls, 2×6 exterior walls, advanced framing22½ in
12 in o.c.Tall walls, heavy wall finishes such as stone or tile backer, and some older homes10½ in

Both 16 and 24 divide evenly into 48 and 96, so the edges of standard 4×8 ft sheets of drywall and sheathing always land on a stud. That is why those two spacings became the standard.

12 in on center21 studs
16 in on center16 studs
24 in on center11 studs

What the building code allows

In the US, the International Residential Code sets maximum stud spacing in Table R602.3(5). For Standard-grade or better studs up to 10 ft tall:

Wall type2×4 studs2×6 studs
Bearing wall, supporting a roof and ceiling only24 in24 in
Bearing wall, supporting one floor plus roof and ceiling16 in24 in
Bearing wall, supporting two floors plus roof and ceilingNot allowed16 in
Non-bearing wall (up to 14 ft for 2×4)24 in24 in

Utility-grade studs are limited to 16 in on center. When bearing studs are at 24 in and the joists or rafters above are more than 16 in apart, each joist or rafter must sit within 5 in of a stud below, which is why 24 in framing usually lines the studs up with the roof trusses.

Local codes can be stricter, especially in high-wind and seismic areas. Check with your building department before framing a load-bearing wall at 24 in.

How many studs each spacing needs

Studs on layout = wall length in feet × 12 ÷ spacing in inches, rounded up, plus one for the end stud. The table counts one straight wall before corners, openings and waste.

Wall length12 in o.c.16 in o.c.24 in o.c.Saved at 24 in
8 ft9752 (29%)
10 ft11963 (33%)
12 ft131073 (30%)
16 ft171394 (31%)
20 ft2116115 (31%)
24 ft2519136 (32%)
30 ft3124168 (33%)
40 ft41312110 (32%)

Worked example: a 40 ft wall with two corners and two openings needs 31 studs on layout at 16 in, plus 8 extras and 10% for culls: 43 studs. At 24 in it is 21 + 8 + 10% = 32 studs, saving 11 studs on one wall.

Count your own walls

The stud calculator adds corners, wall intersections, openings, plates and waste, at 12, 16 or 24 in on center.

16 vs 24 inches: pros and cons

16 in on center24 in on center
Studs neededMoreAbout a third fewer
Insulation15 in wide batts23 in wide batts; fewer studs means less heat loss through the framing
Drywall on walls½ in standard½ in allowed; walls feel slightly less stiff
Drywall on ceilings½ in⅝ in, or ½ in sag-resistant ceiling board, installed across the framing
Hanging cabinets and TVsMore studs to fasten toMay need blocking added before drywall
Floors aboveAllowed with 2×4sNeeds 2×6 studs

24 in spacing is a core part of advanced framing (also called optimum value engineering), which aligns studs with the trusses above and uses fewer extra studs at corners and openings. It saves lumber and improves wall insulation, but plan blocking for anything heavy you'll hang later.

How to find studs in a finished wall

  1. Start at a corner. Layouts usually start from one end of the wall, so studs often fall at 16 in, 32 in, 48 in, 64 in, 80 in, 96 in and so on from the corner. Framers mark the edge of the first stud at 15¼ in, which puts its center at 16 in, where a sheet edge lands.
  2. Look for clues. Outlets and switches are mounted on the side of a stud. Baseboard and trim nails, and slight dimples in painted drywall, often line up with studs.
  3. Use a stud finder and mark both edges of the stud. The center is halfway between them.
  4. Confirm with a small nail in a spot the trim or picture will cover. Solid resistance means wood; if it slides through, move over ¾ in and try again.

Once you find one stud, measure 16 in to the next. If it isn't there, try 24 in. Older homes often have uneven spacing, so check each one before hanging anything heavy.

Framing tips

  • Keep the layout going across the whole wall, even through openings, so sheet edges stay on studs.
  • Add blocking before drywall wherever cabinets, grab bars, handrails or a wall-mounted TV will go.
  • Ceiling framing at 24 in needs ⅝ in drywall or ½ in sag-resistant board.
  • Order about 10% extra studs for warped or split pieces you'll cull.
  • Precut 92⅝ in studs give a standard 8 ft wall with a bottom plate and double top plate.

Frequently asked questions

How far apart are wall studs?

Usually 16 inches on center, measured from the middle of one stud to the middle of the next. Some walls, especially newer exterior walls and non-bearing walls, are 24 inches on center.

What does 16 inches on center mean?

It means the centers of neighbouring studs are 16 in apart. Because a 2×4 is 1½ in thick, the open gap between them is about 14½ in.

Is 24 inch stud spacing allowed?

Yes, for many walls. Under IRC Table R602.3(5), 2×4 bearing walls can be 24 in on center when they support only a roof and ceiling, and non-bearing walls can be 24 in. Walls carrying a floor above need 16 in with 2×4s, or 2×6s at 24 in.

How many studs do I need for a 20 foot wall?

At 16 in on center, 16 studs on layout; at 24 in, 11. Add extras for corners and openings and about 10% for waste.

How far is the first stud from the corner?

Usually 16 in from the corner to the center of the first stud, then every 16 in after that. Framers mark its edge at 15¼ in so its center, where the drywall edge lands, is at 16 in.

Can I use 1/2 inch drywall on 24 inch studs?

On walls, yes. On ceilings framed at 24 in, use ⅝ in drywall or ½ in sag-resistant ceiling board installed across the framing.

Published November 22, 2026. This guide is general information — check local codes and product instructions for your project.

Calculators used in this guide

More guides